PG电子案例

MPE(S)系列潜水切割泵绞刀泵MPE(S)系列潜水切割泵绞刀泵的用途社区、市政管网、综合污水处理厂、大楼地下室汚水处理设备、地铁工程等，尤其适合介质中含长纤维之废水。食品、皮革、纸浆、印染、钢铁等产品的污水排放。屠宰场所、农村沼气池的汚水排放。工业用排水、其它用水、其他用途之排水。For sewage removal from &nb

在线预约

产品详情 PRODUCT DETAILS

MPE(S) 系列潜水切割泵绞刀泵

MPE(S)系列潜水切割泵绞刀泵的用途

社区、市政管网、综合污水处理厂、大楼地下室汚水处理设备、地铁工程等，尤其适合介质中含长纤维之废水。食品、皮革、纸浆、印染、钢铁等产品的污水排放。

屠宰场所、农村沼气池的汚水排放。

工业用排水、其它用水、其他用途之排水。

For sewage removal from living unit and house in scattered settle ment where the laying of a conventional sewer would be too expensive,or where large ground undulation are present, or where it is only possible to lay pipe lines of small diameter.

For sewage removal from motorway resting sites, communal buildings and for renovation of buildings or parts of a city.

For use in slaughter houses,food processing plant, paper factories, agriculture and similar areas.

泵运行介质 /Medium Pumped

Faecal matter and heavily polluted sewage, max. medium temperature： continuous operation =40*C, if unit submerged, shortterm to 60tJ

连续长期运行温度小于 40 °C ,整机浸没，短时运行温度小于 60 °C 。

设计 Design

The water pressure-tight encapsulated fully flood-proof motor and the pump section form a compact robust unit construction.

Motor： Three-phase 380-415V or single-phase 220-240V 50Hzor 60Hz, Insulationclass F. protection type IP68,cooled by amply dimensioned cooling areas.

电机：三相鼠笼式电机 380-415V,或单相220-240V,频率为50或60Hz.絶缘等级F级，防护等lP68o

Bearing： The motor shaft is supported in lubricated-for-life maintenance -free ball bearings.

轴承：进口 NSK轴承。

Shaft Sealing between motor and hydraulic section and motor side by means of high quality sealing units using two silicon carbide mechanical seals, independent of direction of rotation and resistant to temperature shock.

机械密封：釆用双道串联式机械密封。

Discharge/ 出水口径： MP75-4OO=DN5O with ISO-flange

MP550-750=DN80 with ISO-flangea

Shredding System consisting of spiral bottom plate with stationary cutter ring with cutting edges and a shredding rotor located before the impeller for optimum blockage-free running.

水泵部件设计先进合理，水泵叶轮前加装切割旋转刀头，进水口部装固定刃，使被抽吸介质中的杂质在进入叶轮流道之前，被彻底绞碎，无堵塞现象。

TCS— Thermo— Control— System by means of thermal sensor in the stator to give a warning and switch off the motor in the event of excessive temperature occurring.

温度过热保护：电机内预置热敏开关，当温度大于 135°C时，自动断开，保护电机。

DI—System for Seal Monitoring consisting of an electrode in the oil chamber and optical and/or acoustic inspection indication should leakage at the shaft sealing occur.

泄漏监测：油室内安装泄漏监測探头。